Heatstrip Elegance 2400 Watt

Extension mount bracket to Heatstrip Design 

Enables the joining of multiple amplifiers in a small line, which can be done with an extension rod, for maximum heat output.

• The bracket allows a gap of 50 mm between units and the opening for the power connection.
• Brackets can be used for ordinary ceiling, wall mounting or extension brackets.

Wire mounting bracket for Heatstrip Elegance in white

Features

• Allows for a movable patio heater

Compatible with:

• Elegance 1800, 2400 and 3600W

Portable mount for Heatstrip Design

Portable mount designed for Heatstrip heaters. With this mount, it is possible to move a heater around to one's liking, quick and easy. Use this mount with heaters to avoid drilling in walls/ceilings.

Features

• Can be used indoors and outdoors
• High quality
• Wheels attached to mount, allowing for easy transportation

 Included in delivery

• Mount
• Wheels

NOTE: heater must be bought separately. 

Installation

It is recommended to only use the mount for 1800W, 2200W and 2400W heaters, as these can be installed at your own discretion. Heaters with greater amperage must thereby be installed by a licensed electrician.

 In the case of bigger heaters, it is recommended to take the weight into account when installing it, as they may require to be mounted on the floor with screws to ensure stability (screws must be bought separately). 

Extension mount bracket to Heatstrip Intense

The extension brackets designed for Heatstrip Intense will help you to hang the heater exact where you want it to be. The brackets are available with 25 x 25 x 1mm tubes, and can only be supplied as fittings for adjustments to the length or the cut. They can also be supplied as a complete set of fittings, pre-cuts rods and connectors.

• Available in different lengths.
• The mount brackets contain brackets, pre-cut rods and connectors.

Extension mount bracket to Heatstrip Intense

The extension brackets designed for Heatstrip Intense will help you to hang the heater exact where you want it to be. The brackets are available with 25 x 25 x 1mm tubes, and can only be supplied as fittings for adjustments to the length or the cut. They can also be supplied as a complete set of fittings, pre-cuts rods and connectors.

• Available in different lengths.
• The mount brackets contain brackets, pre-cut rods and connectors.

Extension mount bracket to Heatstrip Intense

The extension brackets designed for Heatstrip Intense will help you to hang the heater exact where you want it to be. The brackets are available with 25 x 25 x 1mm tubes, and can only be supplied as fittings for adjustments to the length or the cut. They can also be supplied as a complete set of fittings, pre-cuts rods and connectors.

• Available in different lengths.
• The mount brackets contain brackets, pre-cut rods and connectors.

Extension mount bracket to Heatstrip Intense

The extension brackets designed for Heatstrip Intense will help you to hang the heater exact where you want it to be. The brackets are available with 25 x 25 x 1mm tubes, and can only be supplied as fittings for adjustments to the length or the cut. They can also be supplied as a complete set of fittings, pre-cuts rods and connectors.

• Available in different lengths.
• The mount brackets contain brackets, pre-cut rods and connectors.

Heatstrip Elegance 2400 Flush mount enclosure

This flush mount enclosure can be used with the Heatstrip Elegance 2400 model, specifically for the installation in ceilings. The mount makes it particular useful if you do not wish for the heater to take up space in the room, and instead integrate it smoothly into a ceiling.

It is recommended to clean the flush mount enclosure once every three months. This is due to potential filth and grime may accumulate in it. In case smoking takes place near the heater, it may be necessary to clean it more often. Cleaning it can be done with a wet cloth without the use of strong cleaning agents.

Features

• Designed for use indoors and outdoors
• Easy to install
• Designed for the Heatstrip Elegance 2400
• Size: 131 x 29 x 12.5 cm
• Screws for mounting not included

Installation

When installing the flush mount enclosure, it is important that wires, insulation or other flammable materials are not in direct contact with it.

• Recommended mounting height: 2.5-2.7 metres
• Maximum mounting height: 3 metres

If the heater is installed at a height greater than the maximum, the efficiency of the heater can diminish.

The manual includes more elaborate descriptions when installing the flush mount enclosure.

Switch and remote control with timer for Heatstrip

Make the operation of Heatstrip heaters easier with remote control. With the remote and switch, you are able to time, as well as turn on/off, all of your Heatstrip patio heaters every 1, 2 or 4 hours. The remote control has a range of 10 meters, making it easy to switch a heater on without having to move.

This remote control can be used for one or more Heatstrip patio heaters, as long as the total power usage does not exceed 16 amps and 220-240V.

Features

• Timer function: 1, 2, or 4 hours
• Can be used for multiple Heatstrip heating units
• Switch can be installed by a licensed electrician
• Must be installed a place without humidity

Included in delivery

• Remote controller
• Wall switch

Remote timer

The remote control allows the heating unit to be switched on/off, has a timer and 3 heat settings: high (100%), medium (70%) and low heat (40%). Additionally, it is possible to set a timer for your heater, allowing it to automatically turn on/off after 1, 2 or 4 hours.

Features

• Select heat settings between: High (100%), Medium (70%) and Low (40%).
• Automatic timer control e.g. 1, 2 or 4 hours.
• Can also be used for multiple heaters.
• Remote control included.
• Must be installed by a licensed electrician.

Included in delivery

• Remote controller
• Control panel for wall